How do you really feel about How to Install a Bathtub?
Setting up a bathtub isn't specifically brain surgery, yet it does need solid plumbing, woodworking, and often, tiling abilities. Changing an old bath tub with a brand-new one is also a reasonably tough project. If the old bathtub is readily obtainable, the project can relocate immediately; if you have to open up a wall surface to get rid of the old bathtub as well as position the new tub, the task is much harder. In either case, the project is within a home handyman's skills, although you will certainly need a helper to leave the old bathtub and also embeded in the new one. Make certain you have actually certified on your own for the work and also fit trying it. As opposed to working with a specialist to take control of a halfway-completed job, it is much better to think about utilizing one before you begin. Opportunities are you might require an expert plumber to make tube links.
This article will aid you set up a brand-new bathtub in your bathroom if you have currently acquired a new tub and do not need to transform the plan of your previous supply of water pipelines.
Your tools and also material list should make up the following:
Removing Old Touches
If you require to replace old taps with new ones as a part of your setup, after that the first thing you need to do is disconnect the supply of water. After doing so, switch on the faucets to drain pipes any water staying in the system. The process of eliminating the existing taps can be rather troublesome because of the restricted gain access to that is usually the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipes. Once the supply pipes have been gotten rid of, make use of the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from transforming during this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any kind of old sealing substance.
Prior to proceeding to fit the brand-new taps, contrast the pipe connections on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will certainly require a plastic connector to avoid damage to the string. One end of the port fits on the plastic tail of the faucet and also the various other end gives a link to the current supply pipelines.
If you need to fit a monobloc, then you will certainly call for lowering couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, position the tap in the mounting hole in the bath/basin guaranteeing that the washers are in place in between the faucet and also the sink. Safeguard the tap in place with the producer provided backnut. Once the faucet is securely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with normal tap connectors. The previous type should be attached to the tap finishes first, tightening up just by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Setting up the Bath tub
Using both wood boards under its feet, place the bathtub in the needed placement. The wood boards are practical in equally spreading out the weight of the bathtub over the area of the boards instead of focusing all the weight onto four small points.
The next goal is to ensure that the bathtub is leveled all round. This can be achieved by checking the level and also readjusting the feet on the tub up until the level reviews degree.
To set up taps, fit all-time low of the furthest flexible tap port to the ideal supply pipeline by making a compression join; then do the exact same for the various other faucet.
Activate the water supply as well as inspect all joints as well as brand-new pipework for leakages as well as tighten them if needed. Load the bath tub as well as likewise inspect the overflow outlet and the regular electrical outlet for leaks.
Ultimately, repair the bath paneling as described in the supplier's user's manual. Tiling as well as sealing around the bathtub must wait up until the bath tub has been utilized a minimum of once as this will certainly settle it into its last placement.
Getting ready for the Installment
First of all, the supporting framework provided with the bath ought to be fitted (if called for) according to the producer's directions. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is necessary to make sure that if the tap comes with a plastic washer, it is fitted in between the bathroom and also the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the faucets system to prevent strain on the bathtub.
Fit the adaptable faucet ports to the bottom of the two faucets making use of 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet with the hole in the bathroom. Make use of the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you use all of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom must now prepare to be fitted in its last setting.
Tiling Around the Bathtub
In the location where the bath fulfills the tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to split an inflexible seal, triggering the water to penetrate the wall surface in between the bath as well as the tiling, bring about issues with dampness as well as feasible leaks to the ceiling below.
You can select from a selection of coloured sealants to blend in your components and fittings. They are offered in tubes as well as cartridges, and also are capable of sealing voids as much as a size of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with spins of drenched paper or soft rope. Bear in mind to constantly fill up the bathtub with water prior to securing, to permit the movement experienced when the tub remains in usage. The sealant can crack rather very early if you do not think about this motion before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also quickly readily available on the market. It is a good idea to fit the tiles utilizing waterproof or waterproof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We are very serious about A Step-by-Step Guide to Installing a Bathtub and I really hope you enjoyed reading our piece. Sharing is good. You just don't know, you may be doing someone a favor. Many thanks for your time. Come back soon.
Quick fix? Dial now.